The birch plywood was tricky to stain.

Item: Top Gun Nightstand. Thank you. on Would you build 2 of these to sell unfinished in oak? I built these nightstands using solid oak dimensional lumber as well as 3/4 inch oak veneer plywood. I had to write it all out in order for it to make sense. Using the Kreg jig/pocket hole screws I connected the rails to the stiles which are the two side panels. Are the build plans more detailed a d what were your costs?

It can blotch very easily. Before installing the rear rails I first cut a 1/4 inch wide x 1/2 inch deep slot in the bottom of the 1 x 3 and a 1/4 inch wide x 1/4 inch deep slot in the top of the 1 x 2. Night Stand With Locking Secret Hidden Drawer: I'm a big fan of hidden compartments. This would result in the same final dimensions of 22"x18". It seems people are assuming the the top is wrapped in 1" x 2". So taking the measurements from the top piece of plywood and adding the 1.5 inches to each side and 1.5 inches to the front you go from 18.5" wide to 21.5" wide and 16.25 inches deep to 17.75 inches deep. Thank 2 years ago Secret Compartment (inches): 2 ½H x 20W x12 ½D. Exotic woods are also available, specify the wood species for your project and we will contact you with a price.Hand-applied finish, clear coat lacquer for extra durability, plus hand waxing all speak to the quality and craftsmanship of this gorgeous piece.One Drawer, Two Drawers w/ shelf inside, Magnetic Lock This combination gave the bedside tables a gray/black, almost silver looking finish. About: Married, father of 4 (including triplets) plus 2 Boston Terriers.

I did not fasten the cove at the front as this will be part of the front of the hidden drawer.The sides are built by attaching 1 x 2 x 28 inch oak to the sides of a 15 inch x 25 inch piece of 3/4 inch oak plywood using the Kreg jig. My daytime job is at a Mercedes-Benz car dealership. Thank you! Reply

I’m getting wood from a local cabinet shop and need a list of materials. Sorry, but I forgot to take a picture of the back.I built the 3 main drawers out of 3/4 inch oak plywood.

This is a bit wider than the pieces you can get at the big box stores. Take a close look at the pics. What am I not seeing? What am I not seeing? PaJ58

This isn't the case when looking at the first picture of the top, only 3 sides have the 1"x2" attached. I started by sanding the table with 150 grit sandpaper and followed up with 320 grit until everything was smooth. The dimensional hardwood I used measures 1 3/4 inch x 3/4 inch and is from a local millwork shop near my house. I cut a 16 inch x 21 1/4 inch panel for the back from 1/4 inch plywood. After reading a bunch of comments, I'd like to see if i can shed some light on the top of the piece.

This is also my first instructable. I built these matching nightstands for a friend and his wife. Actual dimensions were 3/4 inch x 5 1/2 inches so I spaced the rails 5 3/4 inches apart to allow for a 1/8 inch gap at the bottom and top of each drawer. The solid oak drawer fronts are fastened to the drawer boxes with screws that are drilled from inside the drawer box front panel into the backside of the 1 x 6 oak boards. I'm working on rendering this in Sketchup and ran into the same issue. I used solid 1 x 6 oak for the drawer fronts.

I mitered all of the corners and tacked them in place with a pin nailer.

I added a 15 inch long oak 1 x 3 (actual size 3/4 inch x 2 1/2 inch) at the top and a 15 inch long oak 1 x 2 at the bottom of the plywood to fit between the 28 inch 1 x 2s.

Using wood glue and pocket hole screws, I assembled the boxes making sure to align the boards with the pocket screws to the front and back. Gel stain worked fairly well but needed a few touch-upsThere is no way I could build these, but this is exactly what I have been hunting for! The tools I used for this project were: miter saw, circular saw, router, air nailer, electric drill, miscellaneous clamps, screws and glue. I made alterations to the top plywood to make the dimensions same as hisTo those that have made this. After removing the dust with a tack cloth I applied a coat of 1 part General Finishes Ebony Dye Stain mixed with 3 parts of their Natural Stain.

In frame and panel construction the vertical pieces of the frame are called stiles and the horizontal pieces are the known as rails. The dimensions for the bedside tables are 28 inches tall x 22 inches wide x 18 inches deep and were copied from the inspiration of this project; the Mason Bedside Table from Potterybarn. These are the dimensions I came up with in my model. For the rear of the table I used a 16 1/2 inch 1 x 3 rail at the top and a 16 1/2 inch 1 x 2 rail at the bottom. This is also my first instructable. I'm a big fan of hidden compartments. 2 years ago MarkK258 were you able to get this rendered in Sketchup? Also, he's not wrapping it with 3/4" moulding. This seems to be how I'm working it out so far. I remember watching the movie "National Treasure, Book of Secrets" and being intrigued by the Resolute Desk with the secret compartment and combination lock using the desk drawers. The drawers are 15 1/2 inches wide x 14 inches deep x 5 inches tall. I also enjoy designing and building my own furniture. I prefer the look of an inset drawer although they require more precision to build than an overlay drawer.

Dil Kya Karay Episode 1, Samsung Digital Inverter Fridge Temperature Setting, Alex Add On Unit Hack, 7 Month Old Baby Pancakes, Gta 5 Mod Menu Ps4 2019, Street Legal Dune Buggy Kits, Killing Them Softly Dave Chappelle, Best Colony Building Games Reddit, James Forrest Bondurant Cause Of Death, 107 Proven Ways To Get The Girl Pdf, Datsun 610 Sss For Sale, Watch Orphee Online English Subtitles, Volvo Vnl 780 Interior Cabinets, Personal Water Craft Are Considered What Type Of Motor Vessel, Suzuki Rm250 For Sale Craigslist, Floor Lamps At Home Depot, Cheap Stackable Plastic Lawn Chairs, Rhino 450 To 660 Swap, Lori Vallow Reddit Theories, Hero Kicks Heroine Out, Tab Soda Publix, Rhino 6 License Key Generator, Catherine Faylen Death, Delayed Reaction To Wasp Sting,