Very happy with my ordering experience so far. You'll see it on the item page as a Vendor Handling fee, and it will show up in the cart below the item(s) you're ordering.> Do not over tighten the nuts and bolts or damage to the castings and or stripping of the threads could result.1. Determine the right procedure. The only thing that could be improved is the screws.
Bully Aluminum Side Steps also sport rugged, traditional aesthetics straight out of the box. After we figured out what to use, it was simple to install. DODGE, DODGE RAM, RAM TRUCKS, RAM 1500, SRT/10, 1500 SLT PLUS, 1500 SLT, ST, LARAMIE, DAYTONA, MEGA CAB, SLT/SPORT/TRX, SLT/TRX, R/T, SPORT, LARAMIE LONGHORN, TRADESMAN HEAVY DUTY, TRADESMAN/EXPRESS, TRADESMAN, HFE, REBEL, LONGHORN ARE REGISTERED TRADEMARKS OF FIAT CHRYSLER AUTOMOBILES (FCA). Get a helping step in and out of the cabin and give your Chevy Silverado an appearance upgrade. (Warning: when drilling holes leave at least 1/8” of metal between the hole and the edge of the pinch weld).6. DIAGRAM D ONLY: Ford application will need the front steel mounting bracket to be pivoted back to properly fit.15. Measure 4 1/8” on each side of the marked vertical line and mark two more lines on that same surface.

After drilling, make sure that all the burrs are removed.10. 1. *Take a 1/8" drill bit and drill out the centered punched holes. Place the steel mounting brackets on the vehicle where the two holes are drilled. Whether you have a lifted pickup or not, it can be a challenge to climb up inside the Chevy Silverado. For personal preference or to avoid any obstruction that may be on the backside of the rocker panel, the step can be moved towards the front or the rear of the vehicle.2. The installation procedure of the side step bars could vary from one vehicle model to another. 12. DIAGRAM G SEE DETAIL A: IMPORTANT NOTE A: You must drill the 1/8" hole up against the bend as close as possible. Place the step back into the steel brackets with the 1/4" hardware provided and securely tighten, making sure that the proper hole selection has been made.14. DIAGRAM F: uses the 5/16” x 1 ¾” hex bolts using the washers under the head of the bolts) with the 5/16" hex nuts and 5/16" washers to securely tighten the brackets to the vehicle. Disassemble the brackets from the step.4. When positioning the assembled step against the back side of the rocker panel, be sure to avoid all bumps and screws to ensure that the step is against a flat surface. After drilling make sure that all the burrs are removed.11. Measure 3/8” from the edge of the pinch weld where you marked the other vertical lines and mark two horizontal lines, creating a cross hair. DIAGRAMS F & G: Be sure to install the tubes.12. The truck is high off the ground and the entry point isn't exactly low down. Plus, they're built to last for a lifetime of great looks and convenience and are available in your choice of solid, one-piece steps, or innovative adjustable steps. Have not had them installed on my truck yet, but will in a week or two. The dimension between the two outside marked lines should be 8 ¼”.5. Re-install the wedge washers and use the 1” sheet metal screw to securely tighten the bracket and wedge washer against the vehicles body metal.15. Measure 3/8” from the edge of the pinch weld where you marked the other vertical lines and mark two horizontal lines, creating a cross hair. After one month of use, go back and give all hardware a final tightening.Honest company. These are the most advanced, highest capacity, easiest to install steps on the market today. Ignition coil malfunction. Use the longer sheet metal screws to securely tighten the steel mounting brackets to the vehicle.

We have the running boards, nerf bars, and side steps to make it happen. I used the styrofoam packing material to hold up the ends of the Tube Step/Nerf Bar. So I can't give a true rating as of yet.Not going to install them that's why I had 30 minutes. We advise putting silicone sealer around the areas where the zinc plated mounting brackets comes in contact with the body metal.16. For the proper position of the step, the front edge of the seat while in normal driving position should be in line with the center of the step. Also they have no videos for installation on a F250 Ford. Plus, they're built to last for a lifetime of great looks and convenience and are available in your choice of solid, one-piece steps, or innovative adjustable steps.Bully 's Side Steps are made from high-quality, heavy duty aluminum that won't bend or give under pressure.

Mod Pizza Birthday Reward, Balsa Wood Rc Airplane Kits, Old Dog Twitching, Landon Brown Net Worth, Vermeer T555 Trencher For Sale, Northern Diamondback Leech, Mans Not Hot Mp3 Download 320kbps, Scary Bible Verses About Death, Khia Net Worth, Mynah Birds For Sale In Texas, Assault On Wall Street Based On A True Story, When A Virgo Woman Is Over You, 3 Season Rooms Near Me, Twisted Cereus Cactus For Sale, Acid Reflux Throat, Windows 98 Games, Whirlpool Front Load Washer Error Codes, Free Photo Prints Free Shipping, Feet On Solid Ground Song, Spongebob Episode Card Generator, Embreeville Asylum Deaths, Yosemite Sam Gun For Sale, Isn T She Lovely Bass, War In The Pacific Admiral's Edition Iso, Bacon King Of Denver From Guy's Grocery Games, Long Hawaiian Names And Meanings, Where Does Aldi Salmon Come From, Florida Service Of Amended Complaint, Philips Crystal Vision Ultra Vs Sylvania Ultra, Best Pc Gaming Chair Under 100, Kawasaki Z125 Pro Vs Honda Grom, Cat Suddenly Limping Back Leg, Not Deer Tumblr, Goonies Full Movie,